€12.90
(tax incl.)
Charging adapter RCA female to Jack male
Max current : 4A
Chargement des images...
Mounting pack for electric kit
For any purchase of an electric kit OZO (radiated motor + controller + accelerator or pedal crank) a mounting pack is offered to facilitate the installation of your electric kit and make it reliable.
€10.00
(tax incl.)
Reference:
000004
Here is the content of the mounting pack:
A spiral sheath to group the wires along the frame (65cm long).
Two cable clamps to secure the controller to the frame (445mm long and 4.6mm wide).
A neoprene protection strip used to protect and fix the motor connectors (125mm long and 130mm wide unfolded). This band is elastic and fixed thanks to a Velcro tape (see photos below).
Three cable ties to secure the wires to the bike frame (200mm long and 4.6mm wide).
Three cable ties to secure the wires to the bike frame (205mm long and 2.5mm wide).
Six cable ties to secure the wires to the bike frame (100mm long and 2.5mm wide).
Two pieces of heat shrink tubing to protect the connectors (40mm long and 18mm in diameter with a reduction ratio of 3: 1).
A piece of heat-shrinkable sheath to protect the connectors (40mm long and 24mm in diameter with a reduction ratio of 3: 1).
Two Anderson clips to put on the engine connector to prevent disconnection thereof.
Two Velcro straps to attach the motor cable (rather than a rislan), this will allow you to disassemble your wheel more easily.
Velcro fastening
Two cable clamps to secure the controller to the frame (445mm long and 4.6mm wide).
A neoprene protection strip used to protect and fix the motor connectors (125mm long and 130mm wide unfolded). This band is elastic and fixed thanks to a Velcro tape (see photos below).
Three cable ties to secure the wires to the bike frame (200mm long and 4.6mm wide).
Three cable ties to secure the wires to the bike frame (205mm long and 2.5mm wide).
Six cable ties to secure the wires to the bike frame (100mm long and 2.5mm wide).
Two pieces of heat shrink tubing to protect the connectors (40mm long and 18mm in diameter with a reduction ratio of 3: 1).
A piece of heat-shrinkable sheath to protect the connectors (40mm long and 24mm in diameter with a reduction ratio of 3: 1).
Two Anderson clips to put on the engine connector to prevent disconnection thereof.
Two Velcro straps to attach the motor cable (rather than a rislan), this will allow you to disassemble your wheel more easily.
Velcro fastening
If you want different lengths and / or additional parts, please specify when ordering.
Customers who bought this product also bought:
€10.00
(tax incl.)
Multifunction switch with two positions.
It can be used as an ON/OFF switch for your lighting or for your OZO controller.
Supplied with 2-pin JST connector.
€2.00
(tax incl.)
XT90 Female 90 connector
Dimensions of the connector: Length 2.5 cm / Width 1 cm / Height 2.2 cm
TECHNICAL SHEET
€3.00
(tax incl.)
The torque arm clamp screws include all the necessary screws, nuts and washers to securely connect your reaction arm (torque arm) to the clamp fixed on the frame or fork of your bike.
Subject to high torsional...
€549.00
(tax incl.)
OZO offers a range of 48V Lithium batteries from 15Ah to 50Ah capacity, i.e. 700Wh to 2400Wh assembled with high-performance Lithium cells and equipped with a BMS with Bluetooth connectivity allowing you to track all...
€9.00
(tax incl.)
Extension for brake handle with cut-off point with sealed Julet 2-way connector for 15A and 22A controller
Julet red 2-way connector compatible with many commercial electric bikes: Cycoo V-5500, TopLife V-5500,...
€9.90
(tax incl.)
This tool will allow you to unscrew the cups of your square-axis bottom bracket.
€29.90
(tax incl.)
10-speed 11-28 cassette in nickel-plated steel compatible with SHIMANO.
Tiering: 11-12-13-14-15-17-19-21-24-28
Weight: 288g.
Leave a review