Filters
Controllers
€6.00
(tax incl.)
This shunt allows to use your Bafang system without any display.
€5.00
(tax incl.)
2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A.
Available in 4 lengths
20cm
50cm
100cm
140cm
€19.00
(tax incl.)
Pedal sensor compatible with the generic 250W controller for the repair of electric bikes.
2 models available: Integrated 12 magnets or V7 6 magnets
The V7 comes with a 6-magnet magnetic washer.
Cable length of 60...
€9.00
(tax incl.)
Extension for brake handle with cut-off point with sealed Julet 2-way connector for 15A and 22A controller
Julet red 2-way connector compatible with many commercial electric bikes: Cycoo V-5500, TopLife V-5500,...
€20.00
(tax incl.)
Standard cable with special lugs for screw terminal block of KELLY controllers.
Standard length: 35cm / Optional extension possible: 50cm, 1m, 1.5m
Cable section: 13AWG / 2,5mm2
+ after wired contact to...
€10.00
(tax incl.)
This brake extension cable has a JST connector available in :
- 30cm
- 50cm
€9.90
(tax incl.)
12x magnets ring for pedelec sensor.
Brand : Kingmeter
Drive side and opposite side available.
For easier installation you can use our support available here
€24.90
(tax incl.)
Y splitter cable to connect one throttle on both controllers. Allows to drive simultanouesly two motors with one throttle.
3 pins JST connectors compatible with OZO controllers 25A, 35A, 40A, 60A and Kelly...
€10.00
(tax incl.)
Eb-bus extender for main harness on your OZO conversion kit.
exists in 3x lengths : 30cm, 80cm, 1m
€10.00
(tax incl.)
This green pushing button switch is expected to be installed on a handlebar or a 22mm tube.
On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or...
€10.00
(tax incl.)
This bracket allows the installation of the bottom bracket sensor on the frame under the crankset, when it is not possible to install the bottom bracket sensor on the vertical frame tube.
The pedal sensor’s probe is...
€10.00
(tax incl.)
Multifunction interruptor with 2 positions
It can be used as a switch for your lighting or your OZO controller
Delivered with 2 JST ways connector
€25.00
(tax incl.)
Standard cable with special lugs for screw terminal block of KELLY controllers.
Standard length: 35cm / Optional extension possible: 50cm, 1m
Cable section: 10AWG / 5mm2
+ after wired contact to switch on the...
€10.00
(tax incl.)
These adapters allow to install the pagnet ring of your pedelec sensor on any bottom bracket standard.
€25.00
(tax incl.)
Standard motor cable with special lugs for screw terminal block of KELLY controllers.
Standard length: 35cm / Optional extension possible: 45cm, 1,1m.
Cable section: 10AWG / 5mm2 + after wired contact to switch on...
The controller (also called variator) is the brain of your electric bike motorization kit. It is an electronic case that manages the motor. The controller receives an information (control signal) from the pedelec or from the full twist throttle and manages the motor power according to this information.
All of our controllers initially include: Anderson Powerpole connectors for power, JST connectors for control, the possibility to connect a throttle or a pedelec, a cut off brake and a cycle analyst.
Our controllers for electric bikes can work with several voltages. This means that you can supply the controllers with various voltages 24V, 36V, 48V and even 72V for some models. To understand better the various controllers’ technologies, please have a look at our “technical information”page.
