Pack front lighting + rear light for electric bike. This kit can be powered by any voltage source from 10V to 55V DC This pack includes: - Front lighting 200 or 600 Lumens. - A rear light 20 or 30 Lumens. Front lamp power cable: 85cm; rear light: 8cm
Thumb throttle with Battery indicator and ON/OOF switch for Ebikes. You can install it on the right or Left side of your handlebar. Available in two Voltage: 36V gauge or 48V.
Accelerator handle complete motorcycle type. Compatible with all electric motorcycles with a handlebar diameter of 22mm. Connector : JST 3 way Sold by the pair.
The new half handle has a much smaller outside diameter than the old one, which allows a perfect integration on the handlebar without generating gear shifting. The diameter is identical to that of the lock-on handles.
Built-in pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame. Compatible with OZO Touring and Enduro kits. Very simple installation. Three-way JST connector. Pedal sensor installation instructions
This "half-handle" type accelerator incorporates a push button that can allow you to turn the engine off when connected to the controller's "brake off" input or to disable the cruise control or activate the horn built into the LED headlight.
This half handle accelerator is compatible with all our kits. The two-position switch can be used to turn off the engine if it is wired to the "brake off" input of the controller or to power your lighting.
This USB charger allows to recharge a phone, a gps thanks to the battery of the bicycle. Compatible with the jst output of the 15A controller of the 250W OZO kit and the 22A controller of the 750W-900W enduro kit. 44x21x11mm Accepts an input voltage from 7 to 60V DC and delivers a constant voltage of 5V with a max load current of 1A.
Motor cable extender 45cm and 1m Phase cable 2.00mm2 and 5x Hall sensors cable 22AWG. Ideal to extend the length of your brushless motor cable.
This ebike accelerator is thumb operated. Designed for right-hand mounting, you can also install it on the left side of your handlebar. Ideal for off-road because you will have a better grip of your handlebar in the technical passages.
This ebike accelerator is thumb operated. This model is mixed, that is to say that you can install it on the right of your handlebar as on the left. Ideal for off-road because you will have a better grip of your handlebar in the technical passages. Supplied with 3-way JST connector.
Half handle type accelerator. Ideal for long rides and people used to motorcycle. Compatible with all our kits.
These adapters allow to install the pagnet ring of your pedelec sensor on any bottom bracket standard.
This brake cut is interesting for bicycles equipped with cable brakes and / or road handlebars or for those who wish to keep their original brake handles It is quick to install on the brake handle or caliper. Connector: JST for the 25A OZO controller.
Magnetic contact JST to activate the brake cut on a bicycle equipped with hydraulic brakes. For 25A and 35A OZO controller You keep your original hydraulic brakes.
Three-position switch to attach to the handlebar of your bike and connect to the dedicated connector of the OZO dual sensorless / sensored controller in order to benefit from three different power modes which are programmed on 30%, 60% and 100% as standard. Note that we can program the three power levels differently by custom programming the controller.
Two-position waterproof multi-function switch. It can be used as an ON / OFF switch for your lighting or for your controller. Supplied without connector.
This brake extension cable of 50cm has a JST connector.
12x magnets ring for pedelec sensor. Drive side and opposite side available.
This extension cable has a 3-way JST connector for pedal sensor or accelerator. With switch 3-Position. Available in 3 lengths :30 cm 50 cm 100 cm
2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A. Available in 4 lengths20cm 50cm 100cm 140cm
©2018 OZO électric