Accessories for OZO 25A and 35A controllers
Find here all the accessories compatible with your OZO 25A or 35A controller and for our OZO industrial controllers
Showing 1 - 45 of 45 items
coupure frein câble connecteur jst
15,00 € In stockThis brake cut is interesting for bicycles equipped with cable brakes and / or road handlebars or for those who wish to keep their original brake handles It is quick to install on the brake handle or caliper. Connector: JST for the 25A OZO controller.
Cycle analyst V3 DPS
199,00 € In StockThe V3 Cycle Analyst is the next step for the CA product line to not only monitor what is going on in an ebike, but also control it. In the V2 CA we included basic throttle over-ride capabilities for speed, current, and low voltage limiting that proved quite popular, but fundamentally it was mostly a passive display. With the V3 Cycle Analyst, all the...3 position switch for OZO controller
15,00 € In StockThree-position switch to attach to the handlebar of your bike and connect to the dedicated connector of the OZO dual sensorless / sensored controller in order to benefit from three different power modes which are programmed on 30%, 60% and 100% as standard. Note that we can program the three power levels differently by custom programming the controller.
Frein à contact JST
15,00 € Product available with different optionsProduct available with different optionsHalf handle accelerator with push button
25,00 € In StockThis "half-handle" type accelerator incorporates a push button that can allow you to turn the engine off when connected to the controller's "brake off" input or to disable the cruise control or activate the horn built into the LED headlight.Half handle accelerator with 2 position button
25,00 € In StockThis half handle accelerator is compatible with all our kits. The two-position switch can be used to turn off the engine if it is wired to the "brake off" input of the controller or to power your lighting.
Thumb throttle with battery gauge and switch for ebikes
30,00 € In StockThumb throttle with Battery indicator and ON/OOF switch for Ebikes. You can install it on the right or Left side of your handlebar. Available in two Voltage: 36V gauge or 48V.Lock-on type half handle accelerator for ebike
25,00 € In StockHalf throttle for ebikes. Delivered with JST 3 pins male connector. Easy to install with "lock-on" collar
pedelec magnet ring holder adapter
10,00 € In StockThese adapters allow to install the pagnet ring of your pedelec sensor on any bottom bracket standard.Hydraulic brake sensor
15,00 € Out of stockMagnetic contact JST to activate the brake cut on a bicycle equipped with hydraulic brakes. For 25A and 35A OZO controller You keep your original hydraulic brakes.
12x magnets ring for pedelec sensor
9,90 € IN STOCK12x magnets ring for pedelec sensor. Brand : Kingmeter Drive side and opposite side available. For easier installation you can use our support available here
3-Way JST extension cable
8,00 € IN STOCKThis extension cable has a 3-way JST connector for pedal sensor or accelerator. With switch 3-Position. Available in 3 lengths :30 cm 50 cm 100 cm
Brake JST extension cable
10,00 € IN STOCKThis brake extension cable has a JST connector available in : - 30cm - 50cmIntegrated crank pedal sensor 4mm JST connector
20,00 € BACKORDERBuilt-in pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame. Compatible with OZO Touring and Enduro kits. Very simple installation. Three-way JST connector. Pedal sensor installation instructionsGreen pushing switch
10,00 € N STOCKThis green pushing button switch is expected to be installed on a handlebar or a 22mm tube. On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or disactivate the speed regulatior or moreover activate the horn On a cart, it can be used to drive the motor by pressureDelivered with 2 JST ways...Bouton poussoir rond rouge
10,00 € N STOCKThis red pushing button is expected to be installed on a handlebar or a 22mm tube. On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or disactivate the speed regulatior or moreover activate the horn On a cart, it can be used to drive the motor by pressureInterrupteur double pour vélo électrique (1 interrupteur 2 positions + 1 bouton poussoir)
14,00 € IN STOCKDouble combined for handlebar installation or 22mm tube. Equipped with two pushing buttons,one green and one red. This product is perfect for activating the forward or backward motion by pressure on an industrial cart, golf cart or any other rolling base. Delivered with a 2 ways JST connector and a 1100mm cable lengthInterrupteur 2 positions rond rouge ON-OFF pour vélo
10,00 € IN STOCKMultifunction interruptor with 2 positions It can be used as a switch for your lighting or your OZO controllerDelivered with 2 JST ways connectorInterrupteur 2 positions rond vert ON-OFF pour vélo
10,00 € BACKORDERMultifunction interruptor with 2 positions It can be used as a switch for your lighting or your OZO controllerDelivered with 2 JST ways connectorInterrupteur pour vélo (bouton poussoir rond rouge + selecteur)
19,00 € IN STOCKThe 2 positions selector coudl be used to start the system or switch on the lighting or in order to select between the forward/backward motion. The red pushing bouton could be used to activate the brake regeneration or the horn. Suitable with every 22mm diameter handlebar Delivered with a 2 ways JST connector and a 1100mm cable lengthSelecteur de mode (2 boutons poussoir)
19,00 € IN STOCKDouble combined for handlebar installation or 22mm tube. Equipped with two pushing buttons, this product is perfect for activating the forward or backward motion by pressure on an industrial cart, golf cart or any other rolling base. Delivered with a 2 ways JST connector and a 1100mm cable length
JST 6-way extension for analyst cycle
10,00 € IN STOCK6-way extension cable cycle analyst30cm 50cm 100cm
2-way JST temperature or lighting probe extension for 25A and 35A controllers, 20cm, 50cm, 100cm and 140cm
5,00 € IN STOCK2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A. Available in 4 lengths20cm 50cm 100cm 140cm
Motor cable extender 45cm and 1m anderson PP30 / JST
20,00 € IN STOCKMotor cable extender 45cm and 1m Extension for motor cable with 3x 2.00mm2 cables for the phases and 5x 0.22mm2 cables for the HALL sensors.The extensions are supplied with Anderson PP30 connectors for the phases and 5-way JST connectors (SM5A) for the Hall sensors.Available in two lengths:45 cm 110 cm Phase cable 2.00mm2 and 5x Hall...
Y splitter cable 3 pins JST for throttle
24,90 € IN STOCKY splitter cable to connect one throttle on both controllers. Allows to drive simultanouesly two motors with one throttle. 3 pins JST connectors compatible with OZO controllers 25A, 35A, 40A, 60A and Kelly controllers and generic controller.Interrupteur 2 positions rond vert ON-OFF pour vélo
12,00 € BACKORDERMultifunction two-position switch. It can be used as a forward/reverse switch, ON/OFF for your lighting, or for your OZO controller. Supplied with a 2-way JST connector.Black brake push button for bike.
12,00 € IN STOCKThis push button is designed for installation on a 22mm handlebar or tube.On a bicycle or motorcycle, it can be used to ground the engine, deactivate the cruise control, or activate the horn. On a cart, it can be used to engage forward motion through pressure.Supplied with a 2-way JST connector.Thumb throttle with switch for ebikes
29,00 € BACKORDERhis accelerator for electric bicycles is activated with the thumb. Cable length: 1m This model is versatile, meaning you can install it on the right or left side of your handlebar. This set includes a waterproof two-position switch that allows you to control lighting or ground your system. It can also be used for forward/reverse movement.Double two positions switches handset
19,00 € IN STOCKThis handset including two switches (2x positions switches) can be used to start the system or switch on the lighting or in order to select between the forward/backward motion. Suitable with every 22mm diameter handlebar Delivered with a 2 ways JST connector and a 1100mm cable lengthhandset with one pushing button and one ON/OFF switch
14,00 € In Stockhandset with one pushing button and one ON/OFF switch for handlebar installation or 22mm tube. Delivered with a 2 ways JST connector and a 1100mm cable lengthDouble positions siwtches handset
14,00 € IN STOCKDouble positions siwtches handset for handlebar installation or 22mm tube. Delivered with a 2 ways JST connector and a 1100mm cable lengthPush-button throttle
35,00 € In StockGive your electric vehicle precise and responsive control with this motorcycle-style throttle, specially designed for electric bikes, scooters, e-motorcycles, and e-scooters. Thanks to its ergonomic design and robust construction, it provides a comfortable grip and excellent durability, even under intensive use. FeaturesProgressive motor control...
Showing 1 - 45 of 45 items
