€25.00
(tax incl.)
Magnet ring specially designed for carbon frame road bicycle with compact crankset.
Chargement des images...
JST pedal box sensor for OZO controller
Pedal sensor in housing for OZO controller 25A and 35A.
For cases with external bearings such as Shimano hollowtech, choose the "transmission side".
Very simple installation.
3-way JST male connector.
Installation instructions for the bottom bracket sensor
€20.00
(tax incl.)
Reference:
002208
You may also like
€20.00
(tax incl.)
Kingmeter pas sensor 12 magnets with waterproof connector Julet Z309AG yellow.
Matching with all 15A and 22A OZO controllers.
câble length : 150 mm.
€20.00
(tax incl.)
Built-in integrated pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame.
Compatible with OZO Touring and Enduro kits.
Very simple installation.
Julet three-way...
€10.00
(tax incl.)
This bracket allows the installation of the bottom bracket sensor on the frame under the crankset, when it is not possible to install the bottom bracket sensor on the vertical frame tube.
The pedal sensor’s probe is...
€20.00
(tax incl.)
Pedal sensor for 15A and 22A OZO controllers to be installed on the vertical frame tube
Supplied with the 12-magnet half discs and the probe.
3-way Julet waterproof connector.
Cable length: 120 mm.
End to end...
€39.00
(tax incl.)
Pas sensor for Cycle analyst V3 CA V3. Can be installed on left side or right side of your bike.
€19.00
(tax incl.)
Pedal sensor compatible with the generic 250W controller for the repair of electric bikes.
2 models available: Integrated 12 magnets or V7 6 magnets
The V7 comes with a 6-magnet magnetic washer.
Cable length of 60 cm...
Pedal sensor in housing for OZO controller 25A and 35A.
For cases with external bearings such as Shimano hollowtech, choose the "transmission side".
Very simple installation.
3-way JST male connector.
Customers who bought this product also bought:
€9.00
(tax incl.)
Extension for brake handle with cut-off point with sealed Julet 2-way connector for 15A and 22A controller
Julet red 2-way connector compatible with many commercial electric bikes: Cycoo V-5500, TopLife V-5500,...
€1.45
(tax incl.)
We can cut spokes at your convenience.
Conventional rolled 18/8 stainless steel spoke with constant wire diameter from the head to the thread.
13G spokes (2,3mm diameter)
€0.00
(tax incl.)
Optimized mapping by OZO. The Original Bafang mapping is appropriate for city bike with 44T chainring and can occurs some disappointments for specific profile as MTB, cargo or road bicycle.
Since 2013, OZO has...
€30.00
(tax incl.)
36V 2A or 36V 4A charger (charges 2x faster than the 2A version), light and silent for Lithium battery of electric bike, VAE, electric scooter or any 36V LiMn Lithium battery.
The 36V 2A charger is very compact. We...
€15.00
(tax incl.)
Cable extension for electric bicycle hub motor with waterproof connector 9 Pins Julet Z910AT
Available in three lengths:
- 30cm
- 45cm
- 110cm
€5.00
(tax incl.)
External speed sensor with wheel magnet, compatible with most universal electrical controllers. It transmits the exact speed of the wheel to your screen to precisely manage the electric assistance and display your...
€46.90
(tax incl.)
This bag is easy to install on any bike. You can get it to travel on normal bicycle but also to install your ebike battery.
You can add one neiman to get ON/OFF function on your ebike
€7.00
(tax incl.)
To check the installation of the torque arm on your bike, you can print the plans below, cut out the part and position it on the frame.
2D plan of the M5 leg
2D plan of the M6 leg
Leave a review