Controllers
The controller (also called variator) is the brain of your electric bike motorization kit. It is an electronic case that manages the motor. The controller receives an information (control signal) from the pedelec or from the full twist throttle and manages the motor power according to this information.
All of our controllers initially include:...
coupure frein câble connecteur jst
15,00 € In stockThis brake cut is interesting for bicycles equipped with cable brakes and / or road handlebars or for those who wish to keep their original brake handles It is quick to install on the brake handle or caliper. Connector: JST for the 25A OZO controller.
KELLY battery cable with 150A Anderson connector
35,00 € In StockStandard cable with special lugs for screw terminal block of KELLY controllers. Standard length: 35cm / Optional extension possible: 50cm, 1m, Cable section: 10AWG / 5mm2 + after wired contact to switch on the controller
KELLY battery cable with 50A Anderson connector
25,00 € In StockStandard cable with special lugs for screw terminal block of KELLY controllers.Standard length: 35cm / Optional extension possible: 50cm, 1mCable section: 10AWG / 5mm2+ after wired contact to switch on the controller
KELLY motor cable with XT150 connector
35,00 € In StockStandard motor cable with special lugs for screw terminal block of KELLY controllers. Standard length: 35cm / Optional extension possible: 45cm, 1,1m. Cable section: 10AWG / 5mm2 + after wired contact to switch on the controller
Cycle analyst V3 DPS
199,00 € In StockThe V3 Cycle Analyst is the next step for the CA product line to not only monitor what is going on in an ebike, but also control it. In the V2 CA we included basic throttle over-ride capabilities for speed, current, and low voltage limiting that proved quite popular, but fundamentally it was mostly a passive display. With the V3 Cycle Analyst, all the...
Controller Kelly motor cable
25,00 € In StockStandard motor cable with special lugs for screw terminal block of KELLY controllers. Standard length: 35cm / Optional extension possible: 45cm, 1,1m. Cable section: 10AWG / 5mm2 + after wired contact to switch on the controller
Pedal sensor for generic OZO controller
19,00 € IN STOCKPedal sensor compatible with the generic 250W controller for the repair of electric bikes. 2 models available: Integrated 12 magnets or V7 6 magnets The V7 comes with a 6-magnet magnetic washer. Cable length of 60 cm on the V7
Controller Kelly Battery cable 40A
20,00 € In StockStandard cable with special lugs for screw terminal block of KELLY controllers.Standard length: 35cm / Optional extension possible: 50cm, 1m, 1.5mCable section: 10AWG / 5mm2+ after wired contact to switch on the controller3 position switch for OZO controller
15,00 € In StockThree-position switch to attach to the handlebar of your bike and connect to the dedicated connector of the OZO dual sensorless / sensored controller in order to benefit from three different power modes which are programmed on 30%, 60% and 100% as standard. Note that we can program the three power levels differently by custom programming the controller.15A 250W controller box frame mount
12,90 € In StockThis case will allow you to aesthetically fix your 15A 250W controller on the frame of your bike. The box is installed on the vertical frame tube using two clamps. Your frame tube should have a maximum diameter of 36mm.Main wiring harness for 15A and 22A OZO controller BFG
25,00 € IN STOCKMain wiring harness (Eb-bus) for 15A and 22A OZO controller working with Bafang protocol.coupure frein câble connecteur jst
20,00 € In stockThis 33cm brake cut is interesting for bicycles equipped with cable brakes and / or road handlebars or for those who wish to keep their original brake handles It is quick to install on the brake handle or caliper. Connectors: Julet 2 pins for touring kit controller and enduro and VAE trade.Y splitter cable 3 pins JST for throttle
24,90 € IN STOCKY splitter cable to connect one throttle on both controllers. Allows to drive simultanouesly two motors with one throttle. 3 pins JST connectors compatible with OZO controllers 25A, 35A, 40A, 60A and Kelly controllers and generic controller.
pedelec magnet ring holder adapter
10,00 € In StockThese adapters allow to install the pagnet ring of your pedelec sensor on any bottom bracket standard.
Controller 25A 12V 24V 36V 48V dual sensored sensorless for brushless motor
119,00 € In StockThe OZO controller 12V 24V 36V 48V integrates high quality electronic components from the automotive world. Dual sensored / sensorless adaptive field-oriented sinusoidal mapping (FOC) will allow you to power all brushless motors BLDC on the market.Hydraulic brake sensor
20,00 € In stockMagnetic contact to activate the brake cut on your 15A or 22A system while maintaining your original hydraulic brakes. Also compatible with all bikes equipped with a 2-way Julet connector. Length 34cm
Controller 12V 15A brushless sensorless
40,00 € In Stock12V 15A controller to power a brushless motor operating in 12V. Sensorless only. Ideal for powering scooter motors in 5" or 6" The controller has the safety function "pedal first", that is to say that it is necessary to start the engine for the accelerator is active.Universal thumb throttle 0-5V linear
20,00 € IN STOCKUniversal thumb throttle 0-5V linear. Easy to install on 22mm pipe
Frein à contact JST
15,00 € Product available with different optionsProduct available with different options
12x magnets ring for pedelec sensor
9,90 € IN STOCK12x magnets ring for pedelec sensor. Brand : Kingmeter Drive side and opposite side available. For easier installation you can use our support available here
Contact brake handle for controller 15A 22A OZO
20,00 € STOCKContact brake handle compatible with the 22A OZO controller You can buy a right handle or a left or the pair. Two colors available: Gray or black.
Rallonge moteur 9 PINS 110cm
15,00 € In stockCable extension for electric bicycle hub motor with waterproof connector 9 Pins Julet Z910AT Available in three lengths: - 30cm - 45cm - 110cmHalf handle accelerator with push button
25,00 € In StockThis "half-handle" type accelerator incorporates a push button that can allow you to turn the engine off when connected to the controller's "brake off" input or to disable the cruise control or activate the horn built into the LED headlight.
Mini scooter controller 36V 250W
45,00 € In stockMini scooter or kick scooter controller 36V 250W. Pedal first function, lcd display, active regenerative braking with throttleHalf handle accelerator with 2 position button
25,00 € In StockThis half handle accelerator is compatible with all our kits. The two-position switch can be used to turn off the engine if it is wired to the "brake off" input of the controller or to power your lighting.40A 48V to 72V FOC brushless bldc motor controller
179,00 € IN STOCKController 48V to 72V - 40A dual sensored sensorless for brushless motor. Compatible with cycle analsyt V2 andV3, throttle, pas sensor, cruise control, backward and forward selection, ebrake cut off, regen Programmable mapping and automatic swapping from sensored map to sensorless map if hall sensors are damaged. Recommended with our direct drive...
Thumb throttle with battery gauge and switch for ebikes
30,00 € In StockThumb throttle with Battery indicator and ON/OOF switch for Ebikes. You can install it on the right or Left side of your handlebar. Available in two Voltage: 36V gauge or 48V.Lock-on type half handle accelerator for ebike
25,00 € Out of stockThe new half handle has a much smaller outside diameter than the old one, which allows a perfect integration on the handlebar without generating gear shifting. The diameter is identical to that of the lock-on handles.
Displays selection for wheel motor 250W to 750W
89,00 € In StockOZO offers 3x different display models. The display is the screen on the ebikes handlebar. It shows all electrical and run datas such as battery state of charge, speed, distance and allows to select the assist power between 9 different levels.Hydraulic brake sensor
15,00 € Out of stockMagnetic contact JST to activate the brake cut on a bicycle equipped with hydraulic brakes. For 25A and 35A OZO controller You keep your original hydraulic brakes.
Ebikes pas sensor Kingmeter under bottom bracket
20,00 € IN STOCKKingmeter pas sensor 12 magnets with waterproof connector Julet Z309AG yellow. Matching with all 15A and 22A OZO controllers. câble length : 150 mm.
Kelly controller 100A KLS7245N 36V 48V 60V 72V
349,00 € STOCKHigh Performance Sine wave Controller for Lithium battery up to 72V. Rated current is 100A. Max current is 320A (30s).This driver is perfect for all projects using Brushless motor suche as electric boat, motorcycle or AGV.
Brake JST extension cable
10,00 € IN STOCKThis brake extension cable has a JST connector available in : - 30cm - 50cm
3-Way JST extension cable
8,00 € IN STOCKThis extension cable has a 3-way JST connector for pedal sensor or accelerator. With switch 3-Position. Available in 3 lengths :30 cm 50 cm 100 cmZEFAL Z Frame bag for OZO controller and battery 100Wh
20,00 € IN STOCKThe Z Frame Pack is a frame bag which is mounted on the horizontal tube at the rear. It is ideal for carrying tools, a mini pump, energy bars, a phone, a rain gear ...Dimensions: 270 x 100 x 80mm / 10.6 x 3.9 x 3.2 "
Kit 250W external 15A controller without motor and battery
229,00 € In StockKit Contrôleur externe OZO 250W - Réparation et Mise à Niveau pour Vélos Électriques Le Kit Contrôleur OZO 250W est la solution idéale pour réparer ou mettre à niveau votre vélo électrique. Ce kit complet comprend un contrôleur, un display, un capteur pédalier adapté, un faisceau de câblage principal et une rallonge moteur 9 PINS. Avec ce kit, vous...Integrated crank pedal sensor 4mm JST connector
20,00 € BACKORDERBuilt-in pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame. Compatible with OZO Touring and Enduro kits. Very simple installation. Three-way JST connector. Pedal sensor installation instructions
Integrated 250W 15A controller kit without motor and battery
254,00 € In StockKit Contrôleur intégré OZO 250W - Réparation et Mise à Niveau pour Vélos Électriques Le Kit Contrôleur OZO 250W est la solution idéale pour réparer ou mettre à niveau votre vélo électrique. Ce kit complet comprend un contrôleur, un display, un capteur pédalier adapté, un faisceau de câblage principal et une rallonge moteur 9 PINS. Avec ce kit, vous...35A FOC controller 24V 36V 48V dual sensored sensorless for brushless motor
159,00 € In StockThis OZO 35A controller is dual sensored / sensorless field oriented (FOC) sinusoidal mapping, which makes it compatible with all brushless electric motors equipped or not with hall sensors. Temperature protection to regulate power when temperature increase. It will be perfect to drive all 1000W to 1500W bldc motors under 24V, 36V and 48V. Compatible...
Touring 250W rear wheel kit with 36V PVC battery
244,00 € In StockThe 250W Touring Rear Wheel Kit is perfect for riders under 80Kg who want light assist system but comfortable assistance for versatile use.Torque 40N.m , Waterproof IP66, color display, The Touring OZO 250W rear wheel motor kitis the most versatile in the range.250W 36V 15A external controller for OZO hub motors
90,00 € In stockThe OZO 15A Controller, equipped with Field-Oriented Control (FOC) technology, ensures optimal performance for OZO Brushless motors. Its IP6-rated tropicalization and waterproof connectors provide exceptional reliability. Installation is made easy with visual keying on each connector, eliminating the risk of connection errors. Elevate your driving...Main wiring harness for 15A and 22A OZO controller
25,00 € IN STOCKMain wiring harness for 15A and 22A OZO controller. 9-way Julet connector.
Touring 250W rear wheel kit with 36V PVC battery
269,00 € In StockThe 250W Touring Rear Wheel Kit is perfect for riders under 80Kg who want light assist system but comfortable assistance for versatile use.Torque 40N.m , Waterproof IP66, color display, The Touring OZO 250W rear wheel motor kitis the most versatile in the range.Green pushing switch
10,00 € N STOCKThis green pushing button switch is expected to be installed on a handlebar or a 22mm tube. On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or disactivate the speed regulatior or moreover activate the horn On a cart, it can be used to drive the motor by pressureDelivered with 2 JST ways...Simplified main harness for display only for wheel motor
25,00 € In stockCable harness to connect your display to your OZO wheel motor.15A Controller integrated in holder for frame battery
115,00 € In StockThe OZO 15A Controller, equipped with Field-Oriented Control (FOC) technology, ensures optimal performance for OZO Brushless motors. Its IP6-rated tropicalization and waterproof connectors provide exceptional reliability. Installation is made easy with visual keying on each connector, eliminating the risk of connection errors. Elevate your driving...Integrated PAS sensor for OZO controller 15A and 22A
20,00 € STOCKBuilt-in integrated pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame. Compatible with OZO Touring and Enduro kits. Very simple installation. Julet three-way waterproof connector. Pedal sensor installation instructionsBouton poussoir rond rouge
10,00 € N STOCKThis red pushing button is expected to be installed on a handlebar or a 22mm tube. On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or disactivate the speed regulatior or moreover activate the horn On a cart, it can be used to drive the motor by pressure22A Controller integrated in holder for frame battery
130,00 € In StockThe OZO 22A Controller, equipped with Field-Oriented Control (FOC) technology, ensures optimal performance for OZO Brushless motors. Its IP6-rated tropicalization and waterproof connectors provide exceptional reliability. Installation is made easy with visual keying on each connector, eliminating the risk of connection errors. Elevate your driving...Interrupteur double pour vélo électrique (1 interrupteur 2 positions + 1 bouton poussoir)
14,00 € IN STOCKDouble combined for handlebar installation or 22mm tube. Equipped with two pushing buttons,one green and one red. This product is perfect for activating the forward or backward motion by pressure on an industrial cart, golf cart or any other rolling base. Delivered with a 2 ways JST connector and a 1100mm cable length
- 1
- 2
Showing 1 - 60 of 110 items
