€25.00
(tax incl.)
Magnet ring specially designed for carbon frame road bicycle with compact crankset.
Chargement des images...
JST pedal box sensor for OZO controller
Pedal sensor in housing for OZO controller 25A and 35A.
For cases with external bearings such as Shimano hollowtech, choose the "transmission side".
Very simple installation.
3-way JST male connector.
Installation instructions for the bottom bracket sensor
€20.00
(tax incl.)
Reference:
002208
You may also like
€20.00
(tax incl.)
Kingmeter pas sensor 12 magnets with waterproof connector Julet Z309AG yellow.
Matching with all 15A and 22A OZO controllers.
câble length : 150 mm.
€20.00
(tax incl.)
Built-in integrated pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame.
Compatible with OZO Touring and Enduro kits.
Very simple installation.
Julet three-way...
€10.00
(tax incl.)
This bracket allows the installation of the bottom bracket sensor on the frame under the crankset, when it is not possible to install the bottom bracket sensor on the vertical frame tube.
The pedal sensor’s probe is...
€20.00
(tax incl.)
Pedal sensor for 15A and 22A OZO controllers to be installed on the vertical frame tube
Supplied with the 12-magnet half discs and the probe.
3-way Julet waterproof connector.
Cable length: 120 mm.
End to end...
€39.00
(tax incl.)
Pas sensor for Cycle analyst V3 CA V3. Can be installed on left side or right side of your bike.
€19.00
(tax incl.)
Pedal sensor compatible with the generic 250W controller for the repair of electric bikes.
2 models available: Integrated 12 magnets or V7 6 magnets
The V7 comes with a 6-magnet magnetic washer.
Cable length of 60 cm...
Pedal sensor in housing for OZO controller 25A and 35A.
For cases with external bearings such as Shimano hollowtech, choose the "transmission side".
Very simple installation.
3-way JST male connector.
Customers who bought this product also bought:
€159.00
(tax incl.)
This OZO 35A controller is dual sensored / sensorless field oriented (FOC) sinusoidal mapping, which makes it compatible with all brushless electric motors equipped or not with hall sensors.
Temperature protection to...
€25.00
(tax incl.)
This half handle accelerator is compatible with all our kits.
The two-position switch can be used to turn off the engine if it is wired to the "brake off" input of the controller or to power your lighting.
€45.00
(tax incl.)
Freewheel 9 speed 11 to 34 teeth standard compatible Shimano
staging: 11,13,15,17,19,21,24,28,34
Weight: 580g
€5.00
(tax incl.)
Original protective cover for Bafang pedal motor.
Only compatible with Bafang BBS01/BBS02 pedals.
Available in 44 teeth or 46/48 teeth
Not compatible with BBSHD.
€19.00
(tax incl.)
The pedal sensor is a rotation sensor. You are required to pedal for assistance and you cannot precisely dose the desired level of assistance since this level is determined by a law of assistance specific to the...
€14.00
(tax incl.)
The Loctite 243 is the essential medium-strength netting brake to secure all the hardware of your electric bike against road and engine vibrations. Ideal for mounting brake discs, crankset motor mounts or torque arms,...
€25.00
(tax incl.)
speed control device for electric bicycle.
On the same principle as your car’s cruise control: you select a cruising speed, you release the accelerator and the electronics regulate the engine power to maintain a...
€10.00
(tax incl.)
This green pushing button switch is expected to be installed on a handlebar or a 22mm tube.
On a bike or a motorcycle, it can be used to stop the motor when it's plugged in on the controller break brake or...
Leave a review