Controllers
The controller (also called variator) is the brain of your electric bike motorization kit. It is an electronic case that manages the motor. The controller receives an information (control signal) from the pedelec or from the full twist throttle and manages the motor power according to this information.
All of our controllers initially include:...
Interrupteur 2 positions rond rouge ON-OFF pour vélo
10,00 € IN STOCKMultifunction interruptor with 2 positions It can be used as a switch for your lighting or your OZO controllerDelivered with 2 JST ways connectorInterrupteur 2 positions rond vert ON-OFF pour vélo
10,00 € IN STOCKMultifunction interruptor with 2 positions It can be used as a switch for your lighting or your OZO controllerDelivered with 2 JST ways connectorUnder frame controller support
14,99 € In stockThis bracket allows to fix the controller under the frame and to let the cables of the derailleur and the brake pass easily.
Interrupteur pour vélo (bouton poussoir rond rouge + selecteur)
19,00 € IN STOCKThe 2 positions selector coudl be used to start the system or switch on the lighting or in order to select between the forward/backward motion. The red pushing bouton could be used to activate the brake regeneration or the horn. Suitable with every 22mm diameter handlebar Delivered with a 2 ways JST connector and a 1100mm cable length
Generic control system to repair electric bikes 250W 36V-48V with LCD Display
139,00 € BACK ORDERRevive your electric bike with our universal kit, designed to be compatible with all rear wheel motors operating at 24V/36V or 36V/48V. Thanks to its sensorless mode, this kit is the perfect solution for repairing a motor even if the Hall sensors are faulty (damaged sensor or broken wire). With only three wires to connect, installation is simple, fast,...Selecteur de mode (2 boutons poussoir)
19,00 € IN STOCKDouble combined for handlebar installation or 22mm tube. Equipped with two pushing buttons, this product is perfect for activating the forward or backward motion by pressure on an industrial cart, golf cart or any other rolling base. Delivered with a 2 ways JST connector and a 1100mm cable length
JST 6-way extension for analyst cycle
10,00 € IN STOCK6-way extension cable cycle analyst30cm 50cm 100cmMain wiring harness for 15A and 22A OZO controller
25,00 € IN STOCKMain wiring harness for 15A and 22A OZO controller. 9-way Julet connector.60A BLDC FOC industrial Controller 24V 36V 48V
199,00 € IN STOCKThe OZO controller 24V 36V 48V 60A integrates high quality electronic components from the automotive world. For electric motors above 1500W and up to 5000W Dual sensored / sensorless adaptive field-oriented sinusoidal mapping (FOC) will allow to power main brushless DC motors (BLDC) which ride at low speed and high torque..Electric motorcycle throttle waterproof connector
30,00 € IN STOCKElectric motorcycle throttle handle with 1m cable and 3x pins female Julet Z309AM waterproof connector. Compatible with all OZO controllers.
2-way JST temperature or lighting probe extension for 25A and 35A controllers, 20cm, 50cm, 100cm and 140cm
5,00 € IN STOCK2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A. Available in 4 lengths20cm 50cm 100cm 140cm
Pack contrôleur trotinette 24V ou 36V
115,00 € In StockMini scooter or kick scooter controller 36V 250W. Pedal first function, lcd display, active regenerative braking with throttle
Motor cable extender 45cm and 1m anderson PP30 / JST
20,00 € IN STOCKMotor cable extender 45cm and 1m Extension for motor cable with 3x 2.00mm2 cables for the phases and 5x 0.22mm2 cables for the HALL sensors.The extensions are supplied with Anderson PP30 connectors for the phases and 5-way JST connectors (SM5A) for the Hall sensors.Available in two lengths:45 cm 110 cm Phase cable 2.00mm2 and 5x Hall...Simplified main harness for display only for wheel motor
25,00 € In stockCable harness Ebbus to connect your display to your OZO wheel motor with Bafang UART Protocol.
Extension cable Julet for bafang display 5 pins or OZO display
12,00 € In StockExtension cable Julet for bafang display 5 pins or OZO display 30cm length
Kelly controller program cable RS232 to JST 4 pins
19,00 € In stockProgramming cable for Kelly JST 4 channel controller to RS232Dsiplay shunt for Bafang electric system
6,00 € IN STOCKThis shunt allows to use your Bafang system without any display.
Hydraulic brake cutoff for Shimano MT200 and MT401 brakes only.
20,00 € BACKORDERMacthing SHIMANO MT200/MT401Adding Motor power off brake sensor make cycling safer Easy assembly and no change with the original brakestructure Braking signal sensitivity is adjustable by user Waterproof rating: lP65There are two versions for left/right assemblyUniversal thumb throttle for 250W 500W 750W OZO and BAFANG motors
20,00 € IN STOCKThis electric bike thumb throttle is compatible with all Bafang mid-drive motor kits and OZO electric wheel kits in 250W, 500W, and 750W configurations. It can be installed on either the right or left side of your handlebars, thanks to its 40cm cable length. Perfect for off-road adventures or hill starts. Comes with a waterproof 3-pin Julet yellow...Interrupteur 2 positions rond vert ON-OFF pour vélo
12,00 € BACKORDERMultifunction two-position switch. It can be used as a forward/reverse switch, ON/OFF for your lighting, or for your OZO controller. Supplied with a 2-way JST connector.
OZO Bluetooth 100A , 190A and 350A controller for Brushless motors with Hall sensors
199,00 € In stockBluetooth 100A, 190A and 350A FOC vector controller for brushless motors. Compatible with 48V, 60V and 72V batteries. This controller is the perfect choice for electrifying motorcycles, karts, boats or any other project requiring sophisticated management of multiple parameters and high power. The smartphone application (IOS and Android) makes it quick...Black brake push button for bike.
12,00 € IN STOCKThis push button is designed for installation on a 22mm handlebar or tube.On a bicycle or motorcycle, it can be used to ground the engine, deactivate the cruise control, or activate the horn. On a cart, it can be used to engage forward motion through pressure.Supplied with a 2-way JST connector.Thumb throttle with switch for ebikes
29,00 € IN STOCKhis accelerator for electric bicycles is activated with the thumb. Cable length: 1m This model is versatile, meaning you can install it on the right or left side of your handlebar. This set includes a waterproof two-position switch that allows you to control lighting or ground your system. It can also be used for forward/reverse movement.Double two positions switches handset
19,00 € IN STOCKThis handset including two switches (2x positions switches) can be used to start the system or switch on the lighting or in order to select between the forward/backward motion. Suitable with every 22mm diameter handlebar Delivered with a 2 ways JST connector and a 1100mm cable lengthBluetooth device for FOC controller 100A 300A 500A
45,00 € IN STOCKThis bluetooth device allows to setup your FOC controller 100A 300A 500A and read all datas in real time.handset with one pushing button and one ON/OFF switch
14,00 € In Stockhandset with one pushing button and one ON/OFF switch for handlebar installation or 22mm tube. Delivered with a 2 ways JST connector and a 1100mm cable lengthDouble positions siwtches handset
14,00 € IN STOCKDouble positions siwtches handset for handlebar installation or 22mm tube. Delivered with a 2 ways JST connector and a 1100mm cable length
Generic controller 250W 36V - 48V to repair any ebikes and mini scooter
70,00 € IN STOCKOperating with or without a handlebar box (display), this controller can repair most original Asian electric-assist bicycles equipped with a brushless motor. Even if the Hall sensors of your motor are faulty, this controller will be able to operate your bicycle. It will also easily operate any 250W brushless motor. Lighting output 6V. Compatible...Kelly Mini KLS7215ND 48-72V 150A programmable sinewave controller.
219,00 € BACKORDEROperates within a voltage range of 48V to 84V DC. 80A continuous and 150A max IP66 waterproof rating This controller will be perfect for your electric motorcycle projects, industrial machines, or any project requiring numerous adjustable parameters and high power. Note: The programming cable is essential for configuring the controller with your motor.
FOC liquid cooling controller 190A and 350A for BLDC PMSM motors with encoder
299,00 € In stockBluetooth 100A, 190A 350A, 450A and 500A FOC vector controller for brushless motors. Compatible with 48V, 60V and 72V batteries. This controller is the perfect choice for electrifying motorcycles, karts, boats or any other project requiring sophisticated management of multiple parameters and high power. The smartphone application (IOS and Android)...
- 1
- 2
Showing 61 - 109 of 109 items
