€50.00
(tax incl.)
Gift voucher worth 50 € to 200 €
Valid for 1 year on all products on the site
Chargement des images...
Mounting pack for electric kit
For any purchase of an electric kit OZO (radiated motor + controller + accelerator or pedal crank) a mounting pack is offered to facilitate the installation of your electric kit and make it reliable.
€10.00
(tax incl.)
Reference:
006784
You may also like
€10.00
(tax incl.)
For any purchase of an electric kit OZO (radiated motor + controller + accelerator or pedal crank) a mounting pack is offered to facilitate the installation of your electric kit and make it reliable.
Here is the content of the mounting pack:
A spiral sheath to group the wires along the frame (65cm long).
Two cable clamps to secure the controller to the frame (445mm long and 4.6mm wide).
A neoprene protection strip used to protect and fix the motor connectors (125mm long and 130mm wide unfolded). This band is elastic and fixed thanks to a Velcro tape (see photos below).
Three cable ties to secure the wires to the bike frame (200mm long and 4.6mm wide).
Three cable ties to secure the wires to the bike frame (205mm long and 2.5mm wide).
Six cable ties to secure the wires to the bike frame (100mm long and 2.5mm wide).
Two pieces of heat shrink tubing to protect the connectors (40mm long and 18mm in diameter with a reduction ratio of 3: 1).
A piece of heat-shrinkable sheath to protect the connectors (40mm long and 24mm in diameter with a reduction ratio of 3: 1).
Two Anderson clips to put on the engine connector to prevent disconnection thereof.
Two Velcro straps to attach the motor cable (rather than a rislan), this will allow you to disassemble your wheel more easily.
Velcro fastening
Two cable clamps to secure the controller to the frame (445mm long and 4.6mm wide).
A neoprene protection strip used to protect and fix the motor connectors (125mm long and 130mm wide unfolded). This band is elastic and fixed thanks to a Velcro tape (see photos below).
Three cable ties to secure the wires to the bike frame (200mm long and 4.6mm wide).
Three cable ties to secure the wires to the bike frame (205mm long and 2.5mm wide).
Six cable ties to secure the wires to the bike frame (100mm long and 2.5mm wide).
Two pieces of heat shrink tubing to protect the connectors (40mm long and 18mm in diameter with a reduction ratio of 3: 1).
A piece of heat-shrinkable sheath to protect the connectors (40mm long and 24mm in diameter with a reduction ratio of 3: 1).
Two Anderson clips to put on the engine connector to prevent disconnection thereof.
Two Velcro straps to attach the motor cable (rather than a rislan), this will allow you to disassemble your wheel more easily.
Velcro fastening
If you want different lengths and / or additional parts, please specify when ordering.
Customers who bought this product also bought:
€25.00
(tax incl.)
Main wiring harness (Eb-bus) for 15A and 22A OZO controller working with Bafang protocol.
Limited time offer
€259.00
(tax incl.)
€299.00
OZO offers a wide range of 36V Lithium batteries to tailor your electric experience.
Choose your battery capacity based on your desired range. A 1000Wh battery provides twice the range of a 500Wh battery.
Our 36V...
€25.00
(tax incl.)
SHIMANO compatible 8 speed 11-34 cassette.
Tiering: 11-13-15-18-21-24-28-34
Weight: 346g
€29.90
(tax incl.)
Tubeless ready, double wall, 36 holes, available in 16", 20'', 24'', 26'', 27,5'' and 29''. Strong rim made in France
€59.00
(tax incl.)
These modules allow for the parallel connection of batteries to increase their autonomy.
Compatible only with generic batteries of the same voltage, although the battery capacity may vary.
The small module is...
€10.00
(tax incl.)
For any purchase of an electric kit OZO (radiated motor + controller + accelerator or pedal crank) a mounting pack is offered to facilitate the installation of your electric kit and make it reliable.
Leave a review