€12.50
(tax incl.)
With 5-way JST box with 4 cables.Available in 50cm and 1m.
Chargement des images...
Dual shunt pour cycle anlyst
Current measuring device allowing to connect and monitor simultaneously two controllers or energy sources on a single Cycle Analyst screen. It is the ideal accessory to accurately monitor the consumption of a dual-engine configuration or a dual battery system.
€50.00
(tax incl.)
Reference:
000890
You may also like
€10.00
(tax incl.)
6-way extension cable cycle analyst
30cm
50cm
100cm
€45.00
(tax incl.)
16A Hall Effect Current Sensor for Solar CA V3 Firmware. This shunt is great for solar application such as long travel, suntrip... you will be able to check your production and consumption on the same CA V3 screen.
€45.00
(tax incl.)
Slim digital up and down pushing buttons for limit setttings by pushing buttons as pedal assist limit.
Requires a Cycle Analyst with version 3.1 or later firmware.
Connects to white 3-pins Aux plug on CA3 device.
€24.90
(tax incl.)
This USB charger converter allows to charge any smartphone or camera or GPS directly with any 12V 24V 36V 48V 60V battery.
Output is 5V 2A
Input voltage has to be between 10V and 60V
44x21x11mm
Easy to use
€20.00
(tax incl.)
This potentiometer support for cycle analyst V3, allows an installation of the potentiometer closer to the handle and will allow you to clamp the torque, speed or power of your engine without leaving the hands of the...
€9.90
(tax incl.)
This spacer allows the speed sensor to be offset if it is too far from the magnet.
Essential on fat bikes.
€129.00
(tax incl.)
This Analogger can be plugged on Jack connector of your CA V2 or V3 to record all datas of your system and travel ( for GPS integrated version).
Customers who bought this product also bought:
€39.00
(tax incl.)
Miche Supertype 5-hole Shimano 130 BCD 5x130mm road standard chainrings perfectly compatible with our 5-hole adapter for Bafang pedal motor.
High quality chainrings, machined in Aluminum 7075 for better resistance to...
€199.00
(tax incl.)
The V3 Cycle Analyst is the next step for the CA product line to not only monitor what is going on in an ebike, but also control it. In the V2 CA we included basic throttle over-ride capabilities for speed, current,...
€599.00
(tax incl.)
OZO offers an extensive range of 48V Lithium batteries to tailor your electric experience.
Choose your battery capacity based on your range requirements. A 1000Wh battery will provide you with 33% more range compared...
€25.00
(tax incl.)
Step Down Converter DC-DC
Input : 36V à 72V
Output : 12 V
Current : 10A
dimensions : 63x58x22mm
Weight : 100g
Waterproof grade : IP67
€19.00
(tax incl.)
5 speed freewheel 14 - 28 standard Shimano compatible
staging: 14-17-21-24-28
Weight: 380g.
€5.00
(tax incl.)
2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A.
Available in 4 lengths
20cm
50cm
100cm
140cm
€10.00
(tax incl.)
To check the installation of the torque arm on your bike, you can print the plans below, cut out the part and position it on the frame.
"Base 1 M12" plan
"Base 1 M14" plan
€179.00
(tax incl.)
Controller 48V to 72V - 40A dual sensored sensorless for brushless motor.
Compatible with cycle analsyt V2 andV3, throttle, pas sensor, cruise control, backward and forward selection, ebrake cut off, regen...
Leave a review