€12.50
(tax incl.)
With 5-way JST box with 4 cables.Available in 50cm and 1m.
Chargement des images...
CA3 Digital Aux Input Grin Technologies
Slim digital up and down pushing buttons for limit setttings by pushing buttons as pedal assist limit.
Requires a Cycle Analyst with version 3.1 or later firmware.
Connects to white 3-pins Aux plug on CA3 device.
€45.00
(tax incl.)
Reference:
000431
You may also like
€50.00
(tax incl.)
Current measuring device allowing to connect and monitor simultaneously two controllers or energy sources on a single Cycle Analyst screen. It is the ideal accessory to accurately monitor the consumption of a...
€10.00
(tax incl.)
6-way extension cable cycle analyst
30cm
50cm
100cm
€45.00
(tax incl.)
16A Hall Effect Current Sensor for Solar CA V3 Firmware. This shunt is great for solar application such as long travel, suntrip... you will be able to check your production and consumption on the same CA V3 screen.
€24.90
(tax incl.)
This USB charger converter allows to charge any smartphone or camera or GPS directly with any 12V 24V 36V 48V 60V battery.
Output is 5V 2A
Input voltage has to be between 10V and 60V
44x21x11mm
Easy to use
€20.00
(tax incl.)
This potentiometer support for cycle analyst V3, allows an installation of the potentiometer closer to the handle and will allow you to clamp the torque, speed or power of your engine without leaving the hands of the...
€9.90
(tax incl.)
This spacer allows the speed sensor to be offset if it is too far from the magnet.
Essential on fat bikes.
€129.00
(tax incl.)
This Analogger can be plugged on Jack connector of your CA V2 or V3 to record all datas of your system and travel ( for GPS integrated version).
Narrow profile 2 button up/down digital Aux input for V3.1 Cycle Analyst firmware. Lets you to change any limit or pedal assist setting up or down in a customizable number of steps. The wiring allows it to work in parallel with an analog potentiometer or 3 position switch for independent adjustment of a 2nd limit setting or presets. CA3.0 devices must be updated to 3.1 firmware in order to work.
Customers who bought this product also bought:
€24.90
(tax incl.)
This 50cm cable get Anderson PP30 and MC4 Solar solar connectors. ideal to connect your solar panels to your OZO 300W or 600W or Genasun solar charger.
€149.00
(tax incl.)
Battery charger LIMN 48V 10A.
Charging voltage 54.6V.
Charge Connector: Anderson.
Charging cable length: 1050 mm.
Power cable length: 1500 mm.
Charger size: 173x89x63 mm.
Weight: 1050 gr.
€49.00
(tax incl.)
Special MTB plate in 32, 34, 36 or 38 teeth NARROW WIDE black anti-derailment.
This plate machined in Aluminum 7075 will be the best choice for mountain biking with your Bafang crankset motor.
Perfectly adaptable on...
€35.00
(tax incl.)
Rear lamp with a light intensity of 30 Lumens weighing only 20 grams.
The advantage of this lamp is its small size it can be easily installed where there is very little space.
It can also be connected directly to...
€8.00
(tax incl.)
This extension cable has a 3-way JST connector for pedal sensor or accelerator. With switch 3-Position. Available in 3 lengths :
30 cm
50 cm
100 cm
€15.00
(tax incl.)
JST magnetic contact to activate the brake cut-off on a bike equipped with hydraulic brakes.
4-way JST connector for compatibility with OZO controllers.
You keep your original hydraulic brakes.
Cable length = 700mm
Leave a review