€0.50
(tax incl.)
Motor shaft spacers are available for any kind of ebikes motor hub and allows to center the wheel inside the frame.
Filters
Spare parts
€1.60
(tax incl.)
Screws for Bafang crankset motor plate.
Sold by 5.
€2.00
(tax incl.)
Bottom bracket for offsetting the Bafang pedal motor if it touches the frame bases, which can be the case on fat bikes or fat bikes.
These spacers can also be used to offset the freewheel body on an in-wheel motor....
€1.20
(tax incl.)
The anti-rotation washer is essential to lock the flat axle of your hub motor in the frame brackets. By preventing it from turning under the effect of torque, it effectively protects your frame and cables from any...
€3.90
(tax incl.)
Grease kit for Bafang central motors overhaul
We advise to change grease inside your central motor every 3000 kilometers
€2.00
(tax incl.)
hub motor nut
M12 for all motors from 250W to 750W
M14 for 1000W motors
€4.50
(tax incl.)
High performance ball bearing with sealed rubber flanges (RS) to effectively protect the internal mechanism from water, dust and impurities. It is specially designed to withstand the rotational constraints of the...
€3.00
(tax incl.)
Set of 6 screws for cassette holder of Freerider engine.
Sold without cassette holder.
€4.50
(tax incl.)
High performance ball bearing with sealed rubber flanges (RS) to effectively protect the internal mechanism from water, dust and impurities. It is specifically designed to meet the rotational constraints of the...
€3.50
(tax incl.)
Essential electronic component allowing the controller to know the exact position of the rotor to ensure a smooth start and an optimal management of the phases of the motor (compatible wheel motor and pedal motor)....
€4.50
(tax incl.)
gasket for Bafang bottom bracket axle on central motors BBSHD.
€3.60
(tax incl.)
Set of 6 screws for cassette holder of Bobber engine.
Sold without cassette holder.
€4.50
(tax incl.)
gasket for Bafang bottom bracket shaft on central Bafang motors BBS01 BBS02. M215 , M315 G340 250W 500W et 750W
€4.50
(tax incl.)
Grease kit for Bafang central motors overhaul
We advise to change grease inside your central motor every 3000 kilometers
€4.90
(tax incl.)
12 x 28 x 7 mm precision ball bearing with rubber sealing (RS) against dust and moisture. Ideal to restore a smooth and backless rotation on your bike components or small engines.
€5.00
(tax incl.)
Original protective cover for Bafang pedal motor.
Only compatible with Bafang BBS01/BBS02 pedals.
Available in 44 teeth or 46/48 teeth
Not compatible with BBSHD.
€5.90
(tax incl.)
Grease kit for Bafang central motors overhaul
We advise to change grease inside your central motor every 3000 kilometers
€6.00
(tax incl.)
This shunt allows to use your Bafang system without any display.
€6.50
(tax incl.)
This high-precision bearing is designed specifically for the repair and internal maintenance of electric bicycle pedal motors. With its strict dimensions of 17 x 35 x 8 mm, it has a reinforced sealing (RS) that...
€15.00
(tax incl.)
Cable extension for electric bicycle hub motor with waterproof connector 9 Pins Julet Z910AT
Available in three lengths:
- 30cm
- 45cm
- 110cm
€7.50
(tax incl.)
Bafang BBS01 BBS02 BBSHD shaft needle roller bearing. Serie M215 M315 M615 MM G340 250W 500W and 750W and 1000W
Note that you have 2x bearings on your BBS01 or BBS02 motor but only one on BBSHD.
€30.00
(tax incl.)
transmission gear for central electric motor OZO. Compatible with 1'' shaft (25,4mm) as all central motor from OZO : moteurs centraux OZO
10 teeth - pas 520 - key 6,35m (1/4'')
10 dents - pas 520 - key 8mm
12...
€8.90
(tax incl.)
The crank lever is the essential tool for properly removing the cranks from your bike during the installation of your electrical kit. Whether you need to mount a crankset motor or position a pedaling sensor (PAS),...
