€12.50
(tax incl.)
With 5-way JST box with 4 cables.Available in 50cm and 1m.
Chargement des images...
Cycle analyst V2 V3 analogger
This Analogger can be plugged on Jack connector of your CA V2 or V3 to record all datas of your system and travel ( for GPS integrated version).
€129.00
(tax incl.)
Reference:
001908
You may also like
€10.00
(tax incl.)
6-way extension cable cycle analyst
30cm
50cm
100cm
€45.00
(tax incl.)
16A Hall Effect Current Sensor for Solar CA V3 Firmware. This shunt is great for solar application such as long travel, suntrip... you will be able to check your production and consumption on the same CA V3 screen.
€50.00
(tax incl.)
Gift voucher worth 50 € to 200 €
Valid for 1 year on all products on the site
€45.00
(tax incl.)
Slim digital up and down pushing buttons for limit setttings by pushing buttons as pedal assist limit.
Requires a Cycle Analyst with version 3.1 or later firmware.
Connects to white 3-pins Aux plug on CA3 device.
€24.90
(tax incl.)
This USB charger converter allows to charge any smartphone or camera or GPS directly with any 12V 24V 36V 48V 60V battery.
Output is 5V 2A
Input voltage has to be between 10V and 60V
44x21x11mm
Easy to use
€20.00
(tax incl.)
This potentiometer support for cycle analyst V3, allows an installation of the potentiometer closer to the handle and will allow you to clamp the torque, speed or power of your engine without leaving the hands of the...
Cycle Analogger
Saves the Cycle Analyst output data to a MicroSD memory card. Data can be read with card reader or USB cable
Comes with:
- USB cable for PC
- DC power cable for connection to battery pack or Cycle Analyst
- Stereo audio Cable for data signal
- Data cable from CA (red to tx, black to gnd)
- 1GB MicroSD card
Dimensions: 80 x 40 x 19 mm
Supply Voltage: 10V - 100V DC
Customers who bought this product also bought:
Limited special offer
€25.00
(tax incl.)
€28.50
The base 3 is in stainless steel of 6.20mm thickness.
To check the installation of the torque arm on your bike, you can print the plan below, cut the part and position it on the frame.
Plan "Base 3 M12"
€299.00
(tax incl.)
This large direct drive motor has a steel stator 35mm wide and a solid axis in 14mm, which allows him to cash a max power of 2000W and to offer a large torque.
It will be perfect for the electrification of a scooter,...
€349.00
(tax incl.)
Brushless BLDC electric wheel 16''
Shipped with reinforced tire 16x2.125 (54-305). External diameter 410mm.
Dropout = 100mm / Kv : 10 RPM/Volt / Torque 70N.m / max speed 25km/h under 36V - 35km/h under 48V
€5.00
(tax incl.)
2-way extension cable for temperature and ON/OFF switch's controller of 25A & 35A.
Available in 4 lengths
20cm
50cm
100cm
140cm
€159.00
(tax incl.)
This OZO 35A controller is dual sensored / sensorless field oriented (FOC) sinusoidal mapping, which makes it compatible with all brushless electric motors equipped or not with hall sensors.
Temperature protection to...
€199.00
(tax incl.)
The V3 Cycle Analyst is the next step for the CA product line to not only monitor what is going on in an ebike, but also control it. In the V2 CA we included basic throttle over-ride capabilities for speed, current,...
€29.00
(tax incl.)
his accelerator for electric bicycles is activated with the thumb.
Cable length: 1m
This model is versatile, meaning you can install it on the right or left side of your handlebar.
This set includes a waterproof...
€20.00
(tax incl.)
This cable allows to update your cycle analyst with the last software version and also to read and set all datas on your computer.
Leave a review