Filters

Subcategories

Price

€0.00 - €60.00

Pedelec

Relevance

adapter pedal board sensor under frame

€10.00 (tax incl.)

This bracket allows the installation of the bottom bracket sensor on the frame under the crankset, when it is not possible to install the bottom bracket sensor on the vertical frame tube. The pedal sensor’s probe is...

Capteur pédalier intégré pour contrôleur 15A et 22A

12x magnets ring for pedelec sensor

€9.90 (tax incl.)

12x magnets ring for pedelec sensor. Brand : Kingmeter Drive side and opposite side available. For easier installation you can use our support available here

Pedal sensor for generic OZO controller

€19.00 (tax incl.)

Pedal sensor compatible with the generic 250W controller for the repair of electric bikes. 2 models available: Integrated 12 magnets or V7 6 magnets The V7 comes with a 6-magnet magnetic washer. Cable length of 60...

Adaptateur 5 trous côté transmission pour boitier compact

pedelec magnet ring holder adapter

€10.00 (tax incl.)

These adapters allow to install the pagnet ring of your pedelec sensor on any bottom bracket standard.

V5 pedal sensor

€19.00 (tax incl.)

The pedal sensor is a rotation sensor. You are required to pedal for assistance and you cannot precisely dose the desired level of assistance since this level is determined by a law of assistance specific to the...

Pedal sensor extension for Cycle Analyst

€12.50 (tax incl.)

With 5-way JST box with 4 cables.Available in 50cm and 1m.

Bottom bracket sensor on frame for OZO 15A and 22A controllers

€20.00 (tax incl.)

Pedal sensor for 15A and 22A OZO controllers to be installed on the vertical frame tube Supplied with the 12-magnet half discs and the probe. 3-way Julet waterproof connector. Cable length: 120 mm. End to end...

JST pedal box sensor for OZO controller

€20.00 (tax incl.)

Pedal sensor in housing for OZO controller 25A and 35A. For cases with external bearings such as Shimano hollowtech, choose the "transmission side". Very simple installation. 3-way JST male connector. Installation...

3-Way JST extension cable

€8.00 (tax incl.)

This extension cable has a 3-way JST connector for pedal sensor or accelerator. With switch 3-Position. Available in 3 lengths : 30 cm 50 cm 100 cm

Pedal sensor on frame for OZO 25A controller JST

€20.00 (tax incl.)

Integrated PAS sensor for OZO controller 15A and 22A

€20.00 (tax incl.)

Built-in integrated pedal sensor for square axle bottom brackets that have a minimum clearance of 4mm between crank and frame. Compatible with OZO Touring and Enduro kits. Very simple installation. Julet three-way...

Capteur pédalier sous boîtier pédalier pour controleur OZO 15A et 22A

Ebikes pas sensor Kingmeter under bottom bracket

€20.00 (tax incl.)

Kingmeter pas sensor 12 magnets with waterproof connector Julet Z309AG yellow. Matching with all 15A and 22A OZO controllers. câble length : 150 mm.

Carbon frame specific PAS sensor magnet ring

€25.00 (tax incl.)

Magnet ring specially designed for carbon frame road bicycle with compact crankset.

Cycle analsyt V3 PAS sensor

€39.00 (tax incl.)

Pas sensor for Cycle analyst V3 CA V3. Can be installed on left side or right side of your bike.

Gigt Voucher 50€,100€,150€, 200€

€50.00 (tax incl.)

Gift voucher worth 50 € to 200 € Valid for 1 year on all products on the site

Find here our full range of pedal sensors for electric bikes.

We offer you different models and different connectors. Be careful to choose the correct connector for your system.

To choose the right sensor model, we invite you to read the assembly instructions for the pedal sensors.

The pedal sensor is a rotation sensor. You have to pedal for assistance. The desired level of assistance is determined by an assistance law specific to the controller and the assistance mode chosen on the handlebar box.