Filters
Composant ki
€25.00
(tax incl.)
This "half-handle" type accelerator incorporates a push button that can allow you to turn the engine off when connected to the controller's "brake off" input or to disable the cruise control or activate the horn built...
€20.00
(tax incl.)
Pedal sensor in housing for OZO controller 25A and 35A.
For cases with external bearings such as Shimano hollowtech, choose the "transmission side".
Very simple installation.
3-way JST male connector.
Installation...
€20.00
(tax incl.)
This 33cm brake cut is interesting for bicycles equipped with cable brakes and / or road handlebars or for those who wish to keep their original brake handles
It is quick to install on the brake handle or caliper....
Limited special offer
€999.00
(tax incl.)
€1,071.40
The Beast ! More than 200N.m of torque. This 1000W middle drive motor BBSHD here in M615 version is a war machine, a Tank ! 6Kg butallows you to climb the trees. It will be perfect for heavy riders over 110Kg, extrem...
€690.00
(tax incl.)
Brushless BLDC 6kW motor to convert any bike 125cc or 250cc into electric. Can also powered electric boat or karting
9,1kg
€25.00
(tax incl.)
Standard cable with special lugs for screw terminal block of KELLY controllers.
Standard length: 35cm / Optional extension possible: 50cm, 1m
Cable section: 10AWG / 5mm2
+ after wired contact to switch on the...
€12.00
(tax incl.)
Multifunction two-position switch.
It can be used as a forward/reverse switch, ON/OFF for your lighting, or for your OZO controller.
Supplied with a 2-way JST connector.
€15.00
(tax incl.)
Support for potentiometer to screw on the back of the V2 or V3 analyst cycle
€25.00
(tax incl.)
This half handle accelerator is compatible with all our kits.
The two-position switch can be used to turn off the engine if it is wired to the "brake off" input of the controller or to power your lighting.
€10.00
(tax incl.)
To check the installation of the torque arm on your bike, you can print the plans below, cut out the part and position it on the frame.
"Base 1 M12" plan
"Base 1 M14" plan
€25.00
(tax incl.)
Standard motor cable with special lugs for screw terminal block of KELLY controllers.
Standard length: 35cm / Optional extension possible: 45cm, 1,1m.
Cable section: 10AWG / 5mm2 + after wired contact to switch on...
€20.00
(tax incl.)
Motor cable extender 45cm and 1m
Extension for motor cable with 3x 2.00mm2 cables for the phases and 5x 0.22mm2 cables for the HALL sensors.
The extensions are supplied with Anderson PP30 connectors for the phases...
€14.00
(tax incl.)
Double positions siwtches handset for handlebar installation or 22mm tube.
Delivered with a 2 ways JST connector and a 1100mm cable length
€699.00
(tax incl.)
This Brushless electric motor PMSM (Permanent Magnet Inner Rotor Motor) with Hall effect sensors is designed to deliver a power of 5000W at 48V, generating a torque of 130 N.m and a maximum rotational speed of 3500...
€12.00
(tax incl.)
In 6.20 mm thick stainless steel
To check the installation of the torque arm on your bike, you can print the plans below, cut out the part and position it on the frame.
Plan "Base 4 M12"
Plan "Base 4 M14"
OZO offers a wide range of components for electric bicycles for the optimization or repair of electric bicycles with wheel motor or pedal motor.
